Showing results: 136 - 150 of 414 items found.
-
-
510170105 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules. Please note this part is too wide for use in multiple adjacent slots (for more information, please reference the attached drawing).
-
510171105 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single Cat 6 connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules. Please note this part is too wide for use in multiple adjacent slots.
-
510171104 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed data inserts (VTAC) to a single USB 5 Gbps (USB 3.0, USB 3.1 Gen 1, USB 3.2 Gen 1) connector. Great for COTS cable configurations. Compatible with all VTAC/SIM ITA modules.
-
510170116 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single DisplayPort connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
510170113 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single HDMI connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
510170108 -
Virginia Panel Corporation
A small, modular PCB board that connects high speed digital inserts (VTAC) to a single 12x InfiniBand connector. Great for COTS cable configurations. Compatible with all VTAC/SIM receiver modules.
-
-
-
540283010060 -
Virginia Panel Corporation
2 PCB Adapters, Receiver, QuadraPaddle, two 192 Position, to 4 PCB-Mounted Male SCSI Connectors (two 510150125)
-
40-200-008 -
Pickering Interfaces Ltd.
This PXI Fault Insertion module is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This module supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses. Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signalling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
40-200-004 -
Pickering Interfaces Ltd.
Each channel can support up to 0.3A and is rated to handle up to 100V between the wire pairs. The wire pairs have controlled transmission line impedance suited to most differential pair signaling systems, including fast CAN Bus interfaces and RS232. Each fault bus is capable of carrying 2A allowing multiple channels to be connected to the same fault condition. Additionally, each fault bus features a changeover relay to allow the user to connect alternative fault conditions to the fault buses.
-
ADQ10GBE -
Teledyne SP Devices
The ADQ10GBE module enables fast network connection from a cPCIe/PXIe chassis to an external host computer. It occupies a single slot in an 3U cPCIe/PXIe chassis and can be used with backplanes supporting up to x8 Gen2 PCIe. All necessary software drivers are included and can be installed on the PXIe controller. ADQ10GBE can be used under Windows 7 (32 or 64 bit), Windows 8 and 8.1, and Linux (native support or ixgbe source code).
-
PCI-7841/cPCI-7841 -
ADLINK Technology Inc.
The PCI-7841/cPCI-7841 is a Controller Area Network (CAN) interface card. It supports a dual-port CAN's interface that can run independently or bridged at the same time. The built-in CAN controller of this card is Philips SJA1000, which provides bus arbitration and error detection with auto correction and re-transmission function.
-
781061-01 -
NI
1-Port PXI CANopen Interface Module—The PXI‑8531 is a high-speed CANopen interface for developing applications with the NI‑Industrial Communications for CANopen driver. CANopen is the application layer that sits on top of the CAN physical layer often used for industrial automation applications. It was designed for motion-oriented machine control networks, such as handling systems, but now it is used in a variety of products and applications, including medical equipment, off-road vehicles, maritime electronics, public transportation, and building automation. The PXI‑8531 can transmit/receive process data objects (PDOs) and service data objects (SDOs) according to CiA DS301. It also features a batch SDO editor with electronic data sheet (EDS) file integration and layer setting services (LSS) support for slave node configuration.